Dataset: Dissolved and particulate elements
Deployment: TN280

Particulate Elements (Twining)
Samples were collected from sub-surface waters using the GEOTRACES GO‐Flo rosette. The filtration was performed directly from pressured GO‐Flo bottles onto membranes (25-mm diameter Supor 0.45-um polyethersulfone) mounted in Swinnex polypropylene filter holders. Filters were cleaned following the protocol outlined in the GEOTRACES Sampling Document (Cutter et al. 2010). Pressurization to <8 psi was achieved with 0.2-um filtered air. Prior to filtration each GO-Flo bottle was gently mixed by manually inverting the bottle several times (after removal of unfiltered salt samples to provide some headspace). Filtration was continued until the entire bottle was empty or 2 hours had elapsed. An average of 4.6-L of water was filtered through each membrane. Filter holders were removed from the GO-Flo bottles and a vacuum applied to remove any residual water. Filters were then folded, stored in acid-washed centrifuge tubes, and frozen at -20 degrees C until digestion and analysis.

Filters were digested in rigorously cleaned 22-mL PFA digestions vials (Savillex). All digestion steps were performed in a Class-100 clean room using standard clean techniques. Filters were first digested in a solution of 25% Optima-grade acetic acid and 0.02 M hydroxylamine hydrochloride following the protocol of Berger et al. (2008). One milliliter of this solution was added to the filter stored in a 1.7-mL polypropylene vial. Following the recommendation of Berger et al. (2008), the solution was heated to 95 degrees C in a water bath for 10 minutes and then allowed to cool to room temperature. The filter was in contact with the acetic acid leach for a total of two hours. The filter was removed to an acid-cleaned PFA bomb and was later digested using the mixture of concentrated acids described below to recover the refractory elements. The acetic acid/hydroxylamine leachate was centrifuged at 14,000 rpm for 10 minutes to sediment all particles. Without disturbing particles on the bottom of the tube, approximately 0.8-mL of leachate was transferred into a 7-mL PFA digestion vial. Optima-grade HNO3 was added (100 uL) to the 7-mL digestion vial, which was subsequently heated uncapped at 110 degrees C to near dryness. Vial contents were redissolved with 2% HNO3 (Optima grade).

The refractory fraction of particulate metals was then measured on the sample filters. The filter was transferred to a 22-mL PFA vial, 2-mL of a mixture of 4M HCl, 4M HNO3, and 4M HF (all Optima grade) was added, and the vial was tightly capped and heated to 110 degrees C for 4 hours. This procedure has been determined to be adequate for digestion of all particulate material, while allowing the Supor filter to remain intact (Ohnemus et al. 2014). Following heating, the acid solution in the bomb was poured into a second PFA vial. To ensure complete transfer of acid, the bombs were thoroughly rinsed with 3 × 0.5-mL aliquots of ultrapure water. This water was also poured into the secondary vial. The secondary vial was then heated to dryness and the contents redissolved with 2-mL of a 50% Optima-grade HNO3 + 15% Optima-grade H2O2 solution. This solution was again dried down and the contents redissolved with 2% HNO3.

All digests were analyzed using a Finnegan-MAT Element2 HR-ICP-MS at the University of Maine following the protocols outlined in Twining et al. (2011). The instrument is equipped with an ESI Apex desolvation nebulizer, an autosampler contained under a HEPA filter, and nickel cones. Cd-111 was analyzed in low-resolution mode, and the remaining isotopes were analyzed in medium-resolution mode. Multiple isotopes were analyzed for some elements, and the isotopes used to derive the reported concentration are as follows for each element: Fe (56 and 57), Cu (63 and 65), Zn (66, 64 and 68). Mean agreement was 2% for the two Cu isotopes, 5% for the two Fe isotopes, and within 3% for the Zn isotopes. Quantification was performed by external calibration, and In-115 was used as an internal standard to correct for variations in instrumental sensitivity during analyses.

Digestions of the certified reference materials BCR-414 (plankton, Community Bureau of Reference, Commission of the European Communities) and PACS-2 (marine sediment, National Research Council of Canada) were done alongside sample digestions in order to assess accuracy. Recoveries were typically within 10% of the certified values (and within the error of the data, taken from replicate measurements). Total elemental recoveries for the Certified Reference Materials (CRMs) are available in the 'Total Elemental Recoveries CRMs' PDF (converted from an original Excel file named 'GEOMics metadata').

Dissolved Fe, Zn, Cu, Mn (Moffett)
500 mL samples were filtered through 0.2 um acropak filters acidified to pH 2 and stored for analysis ashore. Fe, Zn and Cu were analyzed by ICPMS with isotope dilution using the NTA Superflow method developed by Lee et al (2010) and Chappell et al., (2016). Mn was determined using the approach of Field et al., (1999).

Dissolved Cobalt (Saito)
Sample storage and reagent bottles were soaked for >1 week in the acidic detergent Citranox, rinsed thoroughly with 18.2 M-Ohm Milli-Q water (Millipore), filled with 10% HCl to soak for 10 days, and rinsed thoroughly with Milli-Q water adjusted to pH 2 with TM-grade HCl. Reagent purification protocols were identical to those previously published (Saito and Moffett 2001).

Concentrations of total dissolved cobalt were determined using a previously described cathodic stripping voltammetry (CSV) method (Saito and Moffett 2001, Saito et al. 2004). Measurements were made using the Eco-Chemie uAutolabIII systems connected to Metrohm 663 VA Stands equipped with hanging mercury drop electrodes and Teflon sampling cups. Sample preparation was modified slightly to accommodate use of a Metrohm 837 Sample processor, operated with NOVA 1.8 software (Metrohm Autolab B.V.).

For dissolved cobalt analyses, samples were UV-irradiated for 1 h prior to analysis in a Metrohm 705 UV digester to degrade the organic ligands that bind cobalt, enabling full chelation by the added electroactive ligand, dimethylglyoxime (DMG). 11 ml of sample was pipetted into 15ml polypropylene tubes. Recrystallized DMG (0.1M in methanol) was added to a final concertation of 400 uM and purified N-(2-hydroxyethyl)piperazine-N-(3-propanesulfonic acid) (EPPS) buffer (0.5 M in Milli-Q water) was added to a final concentration of 3.8 mM. Tubes were inverted several times before being placed in the autosampler queue, where 8.5 ml of the mixture was dosed into the teflon analysis cup using a 800 Dosino automated burrette (Metrohm). 1.5 ml of purified sodium nitrite (1.5M in Milli-Q water) was added directly to the Teflon cup using a dedicated 800 Dosino burrette. Once loaded, samples were purged with high purity (>99.99%) N2 for 3 min and cobalt concentrations were determined by standard addition, with triplicate measurement of the sample followed by four 25 pM cobalt additions. 5 nM Co stock was diluted from a certified 1ppm reference (SPEX) and added to the analysis cup via a third Dosino burrette.

The analytical blank was determined by analyzing seawater that had been UV-irradiated for 1 h, equilibrated overnight with prepared Chelex 100 resin beads (Bio-Rad), and UV-irradiated a second time to degrade any leached synthetic ligands. Mean blank was 4.6 +/- 0.7 pM, and the detection limit was calculated as triple the standard deviation of the blank, 2.1 pM. A portion of this dataset was published previously in Saito et al. 2014; the blank for those samples was 3.5 pM.

The Saito laboratory has participated in the GEOTRACES intercalibration effort using this electrochemical Co method. Acidified standards were neutralized with concentrated ammonium hydroxide (Seastar), mixing the entire sample between drops, prior to UV digestion. We report our laboratory values for the GEOTRACES and SAFe standard analyses using this electrochemical method, including those conducted during analysis of the EPZT samples to be:
SAFe D1 = 48.5 +/- 2.4 (n=3, at sea),
SAFe D2 = 45.0 +/- 2.7 (n=7),
GEOTRACES GSP = 2.5 +/- 2.0 (n=10),
GEOTRACES GSC = 77.7 +/- 2.4 (n=4).

These results are in good agreement with those from the GEOTRACES intercalibration effort for Co and demonstrate that the methodologies employed to produce this dataset detect concentrations within the standard deviation of current consensus values for UV irradiated samples, which can be found on the International GEOTRACES Program website.

References cited:
Berger, C. J. M., S. M. Lippiatt, M. G. Lawrence, and K. W. Bruland. 2008. Application of a chemical leach technique for estimating labile particulate aluminum, iron, and manganese in the Columbia River plume and coastal waters off Oregon and Washington. Journal of Geophysical Research-Oceans, 113. doi: 10.1029/2007JC004703

Chappell, P. Dreux; Vedmati, Jagruti; Selph, Karen E.; et al (2016) Preferential depletion of zinc within Costa Rica upwelling dome creates conditions for zinc co-limitation of primary production. J. Plankton Res. Volume:38. Issue:2; Pages:244-255. doi: 10.1093/plankt/fbw018

Cutter, G. and others 2010. Sampling and sample-handling protocols for GEOTRACES cruises.

Field, M.P., Cullen, J.T., Sherrell, R.M., (1999). Direct determination of 10 trace metals in 50 mu L samples of coastal seawater using desolvating micronebulization sector field ICP-MS. J. Anal. At. Spectrom. 14, 1425-1431. doi: 10.1039/A901693G

Lee, J.-M., E. A. Boyle, Y. Echegoyen-Sanz, J. N, Fitzsimmons et al. (2011). Analysis of trace metals (Cu, Cd, Pb, and Fe) in seawater using single batch nitrilotriacetate resin extraction and isotope dilution inductively coupled plasma mass spectrometry. Anal. Chim. Acta 686: 93–101, doi: 10.1016/j.aca.2010.11.052

Ohnemus, D.C., M.E. Auro, R.M. Sherrell, M. Langerstrom, P.L. Morton, B.S. Twining, S. Rauschenberg, P.J. Lam. 2014. Laboratory intercomparison of marine particulate digestions including Piranha: a novel chemical method for dissolution of polyethersulfone filters. Limnology and Oceanography, 12:530-547. doi: 10.4319/lom.2014.12.530

Saito, M. A., and J. W. Moffett. 2001. Complexation of cobalt by natural organic ligands in the Sargasso Sea as determined by a new high-sensitivity electrochemical cobalt speciation method suitable for open ocean work. Marine Chemistry. 75 (49-68). doi: 10.1016/S0304-4203(01)00025-1

Saito, M. A., J. W. Moffett, and G. DiTullio. 2004. Cobalt and Nickel in the Peru Upwelling Region: a Major Flux of Cobalt Utilized as a Micronutrient. Global Biogeochemical Cycles. 18 GB4030. doi: 10.1029/2003GB002216

Twining, B. S., S. B. Baines, J. B. Bozard, S. Vogt, E. A. Walker, and D. M. Nelson. 2011. Metal quotas of plankton in the equatorial Pacific Ocean. Deep-Sea Research II, 58:325-341. doi: 10.1016/j.dsr2.2010.08.018