Experimental setup
\nH. akashiwo (CCMP 3374) was isolated from Narragansett Bay June 10, 2010 when in situ water temperature was 21.2\u00b0C. After isolation the culture was maintained at 15\u00b0C. All experiments were conducted with cells that were grown in autoclaved, 0.2 \u00b5m sterile-filtered seawater (30-31 ppt) amended with F/2 media without silica (Guillard 1975). All cultures were maintained under a light intensity of 150 \u00b5mol photons m-2 s-1 and a 12:12 h light: dark cycle. Preliminary experiments to determine the characteristics of this strains\u2019 growth patterns were used to maintain cultures in exponential phase by transferring cultures as needed every 4 to 10 days (depending on growth temperature), resulting in cell densities of 500-24,000 cell mL-1.\u00a0 To avoid convolution of thermal response and effect of unconditioned media just after transfer culture transfers were restricted from 1 day prior and 1 day post change in temperature (Grabski and Tukaj 2008 ).
\nTemperature treatments
\nTemperature was manipulated in the experiment through a series of sequential temperature shifts. Beginning with a culture which had remained at 15 \u00b0C since collection, every four days a triplicate set of the most extreme, current temperature treatments were split with one fraction retained at its current treatment and one fraction shifted a temperature step outward (i.e. further towards the temperature extremes).\u00a0 Only the cultures growing at the highest and lowest temperatures were split and transferred to new temperatures, but all other cultures were continually maintained in exponential growth phase.\u00a0 Cultures maintained at 15 \u00b0C throughout the duration of the experiment served as an acclimated control, and as a reference for the temporal consistency in acclimated rates. Including all temperature steps and extrema, the nine treatments included: 6, 8, 10, 12, 18, 22, 25, 28, 31, and the control at 15\u00b0C. It took 20 days to complete the individual temperature shifts at 4-day intervals to reach the most extreme temperature treatments.
\nDedicated incubators were used for control (15\u00b0C, Model 2015 Low Temperature Incubator, VWR Scientific); 4, 6 (I-41LLVL, Percival Scientific); 8, 18, 22 (I-36LLVL, Percival Scientific); and 10 \u00b0C (Environ Air, Holman Engineering). Twenty-five, 28, and 31 \u00b0C treatments were accomplished with clear 10 L baths controlled by a coupled aquarium heater and thermostat (Fluval, Tru Temp), housed in an illuminated incubator. Light intensity was consistently controlled across temperature treatments.
\nPopulation and growth rate measurements
\nTo quantify changes in cell size, population growth rate, and volumetric growth rate, the abundance and size (Equivalent Spherical Diameter, ESD) distribution of each culture were measured with a 100 \u00b5m aperture on a Beckman Coulter Multisizer 3 (Beckman Coulter, Brea California; Kim and Menden-Deuer 2013). The default bin size was the instrument standard of 0.2 \u00b5m. Each treatment set was measured daily for 15 days following the initial transfer to the target temperature. Experiments were terminated after 15 days because the objective of these experiments was to establish the response to relatively short-term temperature fluctuations. \u00a0
\nStatistical analysis
\nMean and standard deviation of size distribution and cell counts as measured by the Coulter Counter were estimated from the raw data by a gaussian distribution, fit with maximum likelihood estimation to the frequency of particles greater than 8 \u00b5m. Measurements that immediately followed culture inoculation and those from the growth were omitted. Cell volumes were estimated with equivalent spherical diameter (ESD) and spherical shape approximation.
\nThese experiments were conducted at the University of Rhode Island, Graduate School of Oceanography in the laboratory of Dr. Susanne Menden-Deuer
A key component of the effects of temperature on growth and production of phytoplankton is not only through changes in numerical abundance, but also biomass and proxies for biomass such as biovolume. To understand how temperature affected size and biovolumetric growth, repeated measurements of the mean size feature, equivalent spherical diameter (ESD), were recorded for each experimental replicate culture of\u00a0Heterosigma akashiwo\u00a0across a broad range of temperature treatments. These data were collected as part of the experiment designed to study the effect of changing temperature on phytoplankton growth rates.
\nAlso see dataset 'Phytoplankton Growth Acclimation': https://www.bco-dmo.org/dataset/783500
BCO-DMO Processing Notes:
\n-\u00a0added conventional header with dataset name, PI name, version date
\n- reduced precision of ESD from 9 to 1 decimal place
\u00a0