* Sea-Bird SBE 9 Data File:
* FileName = C:\CTD\0611Seibel\ctd01.hex
* Software Version Seasave V 7.21b
* Temperature SN = 2380
* Conductivity SN = 1919
* Number of Bytes Per Scan = 44
* Number of Voltage Words = 5
* Number of Scans Averaged by the Deck Unit = 1
* Append System Time to Every Scan
* System UpLoad Time = Jun 09 2011 22:37:51
* NMEA Latitude = 27 50.20 N
* NMEA Longitude = 111 20.75 W
* NMEA UTC (Time) = Jun 09 2011 22:37:51
* Store Lat/Lon Data = Append to Every Scan
* SBE 11plus V 5.2
* number of scans to average = 1
* pressure baud rate = 9600
* NMEA baud rate = 4800
* surface PAR voltage added to scan
* A/D offset = 3
* Latitude/Longitude added to scan
* GPIB address = 1
* advance primary conductivity  0.073 seconds
* advance secondary conductivity  0.073 seconds
* autorun on power up is disabled
* S>
** R/V New Horizon
** Cruise / PI - Bishop
** May 2011
* System UTC = Jun 09 2011 22:37:51
# nquan = 9
# nvalues = 1112                        
# units = specified
# name 0 = depSM: Depth [salt water, m]
# name 1 = t090C: Temperature [ITS-90, deg C]
# name 2 = sal00: Salinity, Practical [PSU]
# name 3 = sbeox0Mm/Kg: Oxygen, SBE 43 [umol/Kg]
# name 4 = sbeox0PS: Oxygen, SBE 43 [% saturation]
# name 5 = timeS: Time, Elapsed [seconds]
# name 6 = flSP: Fluorescence, Seapoint
# name 7 = par: PAR/Irradiance, Biospherical/Licor
# name 8 = flag: flag
# span 0 =      1.000,    562.000       
# span 1 =     7.8036,    26.8657       
# span 2 =    34.5783,    35.4287       
# span 3 =      0.082,    239.025       
# span 4 =    0.02903,  109.91842       
# span 5 =     57.698,   1774.294       
# span 6 = 1.3245e-01, 4.4886e+00       
# span 7 = 5.3115e-01, 3.8832e+02       
# span 8 = 0.0000e+00, 0.0000e+00       
# interval = meters: 1                  
# start_time = Jun 09 2011 22:37:51 [System UTC, first data scan.]
# bad_flag = -9.990e-29
# <Sensors count="15" >
#   <sensor Channel="1" >
#     <!-- Frequency 0, Temperature -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>2380</SerialNumber>
#       <CalibrationDate>17-May-11 </CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.34079305e-003</G>
#       <H>6.41258189e-004</H>
#       <I>2.33626684e-005</I>
#       <J>2.14937746e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="2" >
#     <!-- Frequency 1, Conductivity -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>1919</SerialNumber>
#       <CalibrationDate>13-May-11 </CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-3.99257945e+000</G>
#         <H>5.25737327e-001</H>
#         <I>-1.01719375e-003</I>
#         <J>8.03830990e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="3" >
#     <!-- Frequency 2, Pressure, Digiquartz with TC -->
#     <PressureSensor SensorID="45" >
#       <SerialNumber>0830</SerialNumber>
#       <CalibrationDate>23-AUG-2010</CalibrationDate>
#       <C1>-4.071823e+004</C1>
#       <C2>-6.785090e-001</C2>
#       <C3>8.050012e-003</C3>
#       <D1>3.124963e-002</D1>
#       <D2>0.000000e+000</D2>
#       <T1>3.008918e+001</T1>
#       <T2>-5.576514e-004</T2>
#       <T3>4.534535e-006</T3>
#       <T4>-1.196359e-008</T4>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#       <T5>0.000000e+000</T5>
#       <AD590M>1.290360e-002</AD590M>
#       <AD590B>-8.201883e+000</AD590B>
#     </PressureSensor>
#   </sensor>
#   <sensor Channel="4" >
#     <!-- Frequency 3, Temperature, 2 -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>4226</SerialNumber>
#       <CalibrationDate>14-May-11 </CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.38172131e-003</G>
#       <H>6.46393778e-004</H>
#       <I>2.22287108e-005</I>
#       <J>1.74718063e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="5" >
#     <!-- Frequency 4, Conductivity, 2 -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>3057</SerialNumber>
#       <CalibrationDate>17-May-11 </CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-1.01967495e+001</G>
#         <H>1.28421270e+000</H>
#         <I>5.01694386e-004</I>
#         <J>2.80776149e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="6" >
#     <!-- A/D voltage 0, PAR/Irradiance, Biospherical/Licor -->
#     <PAR_BiosphericalLicorChelseaSensor SensorID="42" >
#       <SerialNumber>4644</SerialNumber>
#       <CalibrationDate>9/29/09</CalibrationDate>
#       <M>1.00000000</M>
#       <B>0.00000000</B>
#       <CalibrationConstant>2604166666.67000010</CalibrationConstant>
#       <Multiplier>1.00000000</Multiplier>
#       <Offset>0.00000000</Offset>
#     </PAR_BiosphericalLicorChelseaSensor>
#   </sensor>
#   <sensor Channel="7" >
#     <!-- A/D voltage 1, Free -->
#   </sensor>
#   <sensor Channel="8" >
#     <!-- A/D voltage 2, Fluorometer, Seapoint -->
#     <FluoroSeapointSensor SensorID="11" >
#       <SerialNumber>SCF-2958</SerialNumber>
#       <CalibrationDate></CalibrationDate>
#       <!-- The following is an array index, not the actual gain setting. -->
#       <GainSetting>2</GainSetting>
#       <Offset>0.000</Offset>
#     </FluoroSeapointSensor>
#   </sensor>
#   <sensor Channel="9" >
#     <!-- A/D voltage 3, Free -->
#   </sensor>
#   <sensor Channel="10" >
#     <!-- A/D voltage 4, Altimeter -->
#     <AltimeterSensor SensorID="0" >
#       <SerialNumber>1182</SerialNumber>
#       <CalibrationDate></CalibrationDate>
#       <ScaleFactor>15.000</ScaleFactor>
#       <Offset>0.000</Offset>
#     </AltimeterSensor>
#   </sensor>
#   <sensor Channel="11" >
#     <!-- A/D voltage 5, Free -->
#   </sensor>
#   <sensor Channel="12" >
#     <!-- A/D voltage 6, Oxygen, SBE 43 -->
#     <OxygenSensor SensorID="38" >
#       <SerialNumber>0185</SerialNumber>
#       <CalibrationDate>15-Jan-11p</CalibrationDate>
#       <Use2007Equation>1</Use2007Equation>
#       <CalibrationCoefficients equation="0" >
#         <!-- Coefficients for Owens-Millard equation. -->
#         <Boc>0.0000</Boc>
#         <Soc>0.0000e+000</Soc>
#         <offset>0.0000</offset>
#         <Pcor>0.00e+000</Pcor>
#         <Tcor>0.0000</Tcor>
#         <Tau>0.0</Tau>
#       </CalibrationCoefficients>
#       <CalibrationCoefficients equation="1" >
#         <!-- Coefficients for Sea-Bird equation - SBE calibration in 2007 and later. -->
#         <Soc>5.0380e-001</Soc>
#         <offset>-0.5004</offset>
#         <A>-2.6243e-003</A>
#         <B> 8.9518e-005</B>
#         <C>-1.7299e-006</C>
#         <D0> 2.5826e+000</D0>
#         <D1> 1.92630e-004</D1>
#         <D2>-4.64800e-002</D2>
#         <E> 3.6000e-002</E>
#         <Tau20> 2.4000</Tau20>
#         <H1>-3.3000e-002</H1>
#         <H2> 5.0000e+003</H2>
#         <H3> 1.4500e+003</H3>
#       </CalibrationCoefficients>
#     </OxygenSensor>
#   </sensor>
#   <sensor Channel="13" >
#     <!-- A/D voltage 7, Free -->
#   </sensor>
#   <sensor Channel="14" >
#     <!-- SPAR voltage, Unavailable -->
#   </sensor>
#   <sensor Channel="15" >
#     <!-- SPAR voltage, SPAR/Surface Irradiance -->
#     <SPAR_Sensor SensorID="51" >
#       <SerialNumber>6367</SerialNumber>
#       <CalibrationDate>3/18/09</CalibrationDate>
#       <ConversionFactor>1612.65000000</ConversionFactor>
#       <RatioMultiplier>1.00000000</RatioMultiplier>
#     </SPAR_Sensor>
#   </sensor>
# </Sensors>
# datcnv_date = Sep 05 2011 12:10:15, 7.21a [datcnv_vars = 8]
# datcnv_in = C:\Users\Gilly\Desktop\New Horizon 2011_DATA\Ship Data - New Horizon Cruise 6.2011\CTD Data\0611Seibel\ctd01.hex C:\Users\Gilly\Desktop\New Horizon 2011_DATA\Ship Data - New Horizon Cruise 6.2011\CTD Data\0611Seibel\ctd01.XMLCON
# datcnv_skipover = 0
# datcnv_ox_hysteresis_correction = yes
# datcnv_ox_tau_correction = yes
# binavg_date = Nov 12 2013 16:54:20, 7.21a
# binavg_in = C:\Users\Gilly\Desktop\SQUID Field Work\New Horizon 2011_DATA\Ship Data - New Horizon Cruise 6.2011\CTD Data\0611Seibel\ctd01.cnv
# binavg_bintype = meters
# binavg_binsize = 1
# binavg_excl_bad_scans = yes
# binavg_skipover = 0
# binavg_surface_bin = no, min = 0.000, max = 0.000, value = 0.000
# file_type = ascii
*END*