Dataset: GP16 Pb Isotope Ratios
Deployment: TN303

The towed-fish sampling method used was exactly the same as the description in section 2.1 of the GEOTRACES cookbook in a positive-pressure filtered air environment filtered through cleaned 0.2 um Acropak capsule filters (Acropak filters were used for at most 3 stations before a new filter was used, and they were stored empty in a refrigerator while not in use) into warm-acid leached Nalgene 2-liter polyethylene bottles with polypropylene caps, rinsed 3 times with the sample. Bottles were then capped and not further handled until returned to MIT a few months later, where they were acidified to pH 2.0 with high-purity HCl and allowed to sit for a few months before analysis.

Analytical Procedures:
2L high-density polyethylene sample storage bottles with polypropylene caps and their top threads were soaked overnight in 2N reagent grade HCl, then filled with 1N reagent grade HCl to be heated in an oven at 60˚C overnight, inverted, heated for a second day, and rinsed 5X with pure distilled water. The bottles were then filled with trace metal clean dilute HCl (~0.01N HCl) and again heated in the oven for one day on either end. Clean sample bottles were emptied, rinsed with distilled water, and double-bagged prior to shipboard rinsing and filling with sample.

Samples were analyzed at least 1 month after acidification during 7 mass spectrometry sessions by a modified method based on that described Reuer et al. (2003) as modified by Boyle et al. (2012) and further slightly modified as noted in the following.

The isotope method begins with Nobias Chelate PA1 preconcentration followed by anion exchange purification. The PA1 method was used in preference to the Reuer et al. (2003) Mg(OH)₂ method because high Si levels in the Pacific Deep water (which are scavenged by Mg(OH)₂) lead to precipitation of silica gel upon dissolution (preventing column passage). The method starts with a two repeated batch ion-exchange chelation preconcentrations followed by the Reuer et al. (2003) anion exchange purification and isotope ratio analysis on a GV/Micromass IsoProbe multicollector ICPMS using a 50 uL/min nebulizer aspirated into an APEX/SPIRO desolvator, using post-desolvator trace N₂ addition to boost sensitivity.

Nalgene polypropylene separatory funnels (1000mL) and Corning 50 mL conical centrifuge vials were cleaned by heated submersion for 2 days at 60˚C in 1M reagent grade HCl, followed by a bulk rinse and 4X individual rinse of each vial with pure distilled water. Each funnel and vial was then filled with trace metal clean dilute HCl (~0.01M HCl) and heated in the oven at 60˚C for one day on either end. Separatory funnels and centrifuge vials were kept filled until just before usage. The separatory funnels were rinsed with distilled water after each use and then filled with high-purity distilled water spiked with high-purity HCl (final concentration ~0.01M) between uses.

Nobias Chelate PA1 resin was cleaned with 2 methanol rinses, and a distilled water rinse followed by leaching with ultrapure 6M HCl for 12-24 hours. This procedure was repeated twice, followed by two one-day leaches with ultrapure 3M HNO3 on a shaker table. The resin was then rinsed six times with distilled water to remove the nitric acid. It was then leached twice with ultrapure 0.1N HNO₃ for one day each. The final 0.1N rinse was checked for Pb blank by ICPMS and the resin only used if the blank was acceptably low. Because of the large amounts of resin used, the used resin from each sample was saved and re-washed using the following protocol: leach with 3M HNO3 for 1 day, rinse 4x with dH₂O, rinse with 0.1M HNO₃ for 2 days, rinse with fresh 0.1 M HNO₃ for 3 days, and then then rinse with dH₂O until the pH is ~5.

One or two 1000mL polypropylene separatory funnels (Nalgene) were weighed and rinsed one time with seawater sample, then filled with ~1000 mL (with up to 700 mL in the second funnel) of sample. The pH of the solution was adjusted by addition of purified ammonium hydroxide/acetic acid pH=7.98 buffer (to a final pH>4; preferably pH~4.1 to keep the buffer blank low). A pre-cleaned aliquot of Nobias Chelate PA1 resin was added, and agitated on a shaker table for one day. Then the resin was allowed to settle to the bottom of the separatory funnel and drawn off into a 50 mL centrifuge tube. A second batch of Nobias Chelate PA1 resin was then added and agitated for one day on a shaker table. Then the second batch of resin was allowed to settle to the bottom of the separatory funnel and drawn off into the same 50 mL centrifuge tube. The solution/resin mix was centrifuged and the supernatant solution siphoned off. Pb was released from the resin by addition of trace metal clean 0.1M HNO₃ for 1-2 days, then the supernatant was transferred into a clean fluorocarbon vial and taken to dryness on a hotplate in a clean flow fume hood in a positive pressure clean lab. A PA1 resin blank was taken from a batch of resin directly placed into the eluting 0.1M HNO₃ and henceforward treated as a sample.

Eichrom AG-1x8 resin was cleaned by three batch rinses with 6N trace metal clean HCl for a ~12 hours on a shaker table, followed by multiple washes with distilled water until the pH of the solution was above 4.5. Resin was stored at room temperature in the dark until use.

The residue from the samples and blanks was dissolved in 8 drops of high purity 1.1M HBr. The resin in the column was first cleaned with 6M HCl, equilibrated with 1.1M HBr, and then sample was loaded onto the column. The column was then washed with 1.1M HBr followed by 2M HCl and then eluted with 6M HCl. The samples in a 5 ml Savillex PTFE vial were then taken to dryness on a hotplate in a recirculating filtered air fume hood, and stored sealed until analysis.

Just before analysis, samples were dissolved for several minutes in 10ul concentrated ultrapure HNO₃. Then, an appropriate volume of ultrapure water was added (typically ~400ul) and spiked with an appropriate amount of Tl for mass fractionation correction. IsoProbe multicollector ICPMS Faraday cups were used to collect on 202Hg, 203Tl, 205Tl, 206Pb, 207Pb, and 208Pb. An Isotopx Daly detector with a WARP filter was used to collect on 204Pb+204Hg. This Daly detector is a revised version that eliminates a reflection problem with the electronic circuitry of the previous version. Because the deadtime of the Daly detector varied from day to day, we calibrated deadtime on each day by running a standard with known 206Pb/204Pb at a high 204 count rate. The counter efficiency drifts during the course of a day, so we established that drift by running a standard with known 206Pb/204Pb (and a 204 count rate comparable to the samples) every five samples. Tailing from one Faraday cup to the next was corrected by the 209Bi half-mass method as described by Thirlwall (2001).